Honeywell air purifiers are one of the most popular air purifiers in the market. These air purifiers are highly effective in reducing household odor, allergens and other air pollutants. However, once any purifier gets issues, it can't perform well. Most problems come from clogged filters, inlets, outlets and electrical problems. Therefore, we have come up with tips on Honeywell air purifier troubleshooting that helps you maintain optimum performance.
Honeywell Air Purifier Troubleshooting Tips
A Honeywell purifier cleans the air by filtering contaminants floating in your home. These models will use three separate filters for air purification. When your Honeywell air purifier refuses what it is supposed to do, knowing how to fix it can help you. To repair the Honeywell air purifier common problems and get it back up running, look at this post.
Honeywell Air Purifier Replacement Parts - Shop Online!
Air Purifier Stops Working
Some of the reasons behind your air purifier stopped working are:
Bad filter
You have to check for the clogged filter. As the filter in the air purifier cleans the air, it may get clogged with dirt and debris. Then, it can't able to do its job. If the filter is clogged, make sure it needs to be cleaned. Replace if the filter is too dirty.
Broken motor
The air purifier fan could be damaged. You will have to check the fan blades as well as the motor. If the blades are damaged, you should replace them with a new one. A broken motor caused to a high-pitched sound when you turn on your air purifier.
Blown fuse or unplugged cord
Check if the plug has been pulled out of the power outlet accidentally. If there is an electrical surge, then you can find that one or more fuses could be bad. Additionally, you have to verify the fuses.
It's better to try these two things before replacing any part. Also, try moving the power cord back into place so that no wires are stretched too tightly while you are doing this.
To ensure the proper operation of the Honeywell purifier, make sure the outlet has the correct rating.
OEM Honeywell Parts for Air Purifiers - Order at Low Cost!
Improper installation
Your air purifier may get stopped working because of improper installation. Once verify the installation instructions in the manual and confirm whether the installation has been done correctly or not. Some models need specific installations so check if your model needs any special installations.
Too close to a heat duct
See if the air purifier is placed too close to a heat duct. If so, it might cause to overheat and shut down. So, move away from vents or other heat sources.
Many devices on the circuit breaker
If your unit is running low on power, verify the devices which are running on the same circuit breaker. Make sure the amount of electricity provided by the outlet matches what you need so that you won't get the circuits to overload in your home.
Honeywell Air Purifier Keeps Shutting Off
If filters of the air purifier are clogged, your unit will not run as long before it shuts off. So, check and clean the filters if needed.
Overheating
If you observe overheating of your air purifier, turn it in a colder environment and verify if it still shuts off.
Manufacturing defects
If everything else looks good, then there might be a manufacturing defect. In this case, you need to contact customer service or have it replaced.
Genuine and Reliable Honeywell Air Purifier Parts - Buy from PartsAPS!
Honeywell Air Purifier Error Codes
If there is a problem with the device, power cord or electrical wiring, your Honeywell air purifier will give error codes.
Code E-01: This code is because of a blown fuse. You will need to replace it if required.
Code K-05: When the air purifier won't turn on or off, you can get this error code. Try to contact an authorized technician for servicing.
Code E-02: It indicates the overheating. Try turning the air purifier off and leaving it in a colder environment. Also, check if there is faulty wiring going on.
Code L-05: When you see this code, understand that your purifier is not working because of a blown fuse or power outage.
Code L-07: It identifies the error with the electrical wiring and takes the help of a professional to remove the code.
Air Purification is Not Working Well
If your air purification is not working well, you will be able to take unfiltered air. The possible causes are:
- Room coverage is too large.
- Indoor air quality is terrible.
- Objects are blocking the air intake and outlet.
- The dust has built upon the filters.
- The filter might be closed to the corner.
Ventilate the whole room once before start using the air purifier and close all windows and doors when you started.
Final Thoughts
From this post, you will be able to diagnose and solve the most common issues that will affect the performance of your air purifier. However, you may get all these Honeywell air purifier problems with irregular maintenance and incorrect usage. Hence, clean your Honeywell air purifier and clean the filter to ensure optimum efficiency. Check the manual for more Honeywell air purifier instructions.
